Pxi-8106 user manual

News, Events, and Spotlights. In toxic microbial warfare, study finds strength in numbers December 7, Friday, February 4, pm. Together is better: Thriving through connection and cooperation Meet Farzad Sunavala, a first-year student in the Cornell Engineering Management Online Learning program. Graduate Programs Ph. Program M. Riding the waves straight to a Ph.

Thomas Paasch Tell us about yourself. Anita Zhang Why did you choose Cornell? Research Areas. Geotechnical Engineering. Structural Engineering. Transportation Systems Engineering.

Environmental Fluid Mechanics and Hydrology. Environmental Processes. Remove any filler panels blocking access to the system controller slot slot 1 in the chassis. Touch the metal part of the case to discharge any static electricity that might be on your clothes or body. Remove the protective plastic covers from the four bracket-retaining screws as shown in Figure The module will not insert properly unless the handle is in its downward position so that it does not interfere with the injector rail on the chassis.

Tighten the four bracket-retaining screws on the top and bottom of the front panel to secure the NI PXI to the chassis. Connect the keyboard and mouse to the appropriate connectors. Refer to. Figure , Y-Splitter Cable.

Connect devices to ports as required by your system configuration. Power on the display device. Verify that the controller boots. You can place PXI devices in any other slots. To remove the unit from the PXI chassis, complete the following steps:. Remove any cables that may be attached to the controller front panel. Unscrew the bracket-retaining screws in the front panel. Refer to Figure for the location of these screws. Slide the unit out of the chassis. The BIOS is the low-level interface between the hardware and operating system software that configures and tests your hardware when you boot the system.

Caution Changing BIOS settings may lead to incorrect controller behavior and possibly an unbootable controller. In general, do not change a setting unless you are absolutely certain what it does. The setup program loads after a short delay. To use the arrows on the numeric keypad, you must turn off Num Lock.

At the top-level menus, this key serves as a shortcut to the Exit menu. The optimal default values are the same as the shipping configuration default values. The Main setup menu reports the following configuration information:. The Main setup menu also includes the following settings:. Most operating systems also include a way to change this setting. This menu contains BIOS settings that normally do not require modification. If you have specific problems such as unbootable disks or resource conflicts, you may need to examine these settings.

Caution Changing settings in this menu may result in an unstable or unbootable controller. The Advanced setup menu includes the following settings and submenus:. Refer to the Video Configuration Submenu section for more information.

ExpressCard Configuration submenu. Refer to the ExpressCard Configuration Submenu section for more information. Refer to the. Refer to the Trigger Router Configuration Submenu section for more information.

Use this submenu to apply alternate settings to the hard disk drive HDD interfaces. Normally, you do not need to modify these settings, as the factory default settings provide the most compatible and optimal configuration possible. The default value is Enabled.

The default value is AHCI. Use this submenu to apply alternate settings to the CPU. A virtual machine monitor VMM can utilize the additional hardware capabilities provided by the VT-x processor extensions. The default value is. Use this submenu to apply alternate settings to the video configuration.

To use an external video adapter as the primary graphics adapter, choose. Add-in PCI Video. The default value is Onboard Video. The default value is MB. An analog monitor, however, will function with this option set to either Analog or DVI. The DDC communication path is only enabled when set to Analog for an analog monitor, so certain advanced features of your analog monitor may only be enabled when routing DDC to Analog.

The default setting is DVI. Use this submenu to apply alternate settings to the ExpressCard configuration. The default value for this setting is 8 PCI buses. The default value for this setting is 32M bytes of memory. Use this submenu to apply alternate configurations to the USB ports. Note Certain real-time applications may require you to disable this setting to reduce loop time jitter. The default is 20 seconds. Use this submenu to apply alternate configurations to the serial and parallel ports.

Refer to the Serial Port 0 Configuration Submenu section for more information. Refer to the Parallel Port Configuration Submenu section for more information.

The default value is Auto. Usually the default setting works for all applications. Note that the options available vary based upon the Device Mode selected for the parallel port.

Use this submenu to program the front panel trigger router configuration. The front panel trigger can be routed to System Reset , allowing an external trigger to reset the system. The default value is Disabled. Note The settings below override the behavior of the switches on SW1. To use the settings from the switches, select Use Switch Setting for each option. The default is Use Switch Setting. If the target is unable to initiate a DHCP connection, the target connects to the network with a link-local IP address.

Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. National Instruments. Worldwide Technical Support and Product Information ni. Warranty The NI PXI is warranted against defects in materials and workmanship for a period of one year from the date of shipment, as evidenced by receipts or other documentation.

This limitation of the liability of National Instruments will apply regardless of the form of action, whether in contract or tort, including negligence. Copyright Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation. Trademarks National Instruments, NI, ni.

Contents Security Menu This manual, the NI PXI User Manual , contains more details about changing the installation or configuration from the defaults and using the hardware. Conventions The following conventions appear in this manual: » The » symbol leads you through nested menu items and dialog box options to a final action.

This icon denotes a tip, which alerts you to advisory information. This icon denotes a note, which alerts you to important information. This icon denotes a caution, which advises you of precautions to take to avoid injury, data loss, or a system crash.

Bold text also denotes parameter names. Italic text also denotes text that is a placeholder for a word or value that you must supply. About This Manual monospace Text in this font denotes text or characters that you should enter from the keyboard, sections of code, programming examples, and syntax examples. This font is also used for the proper names of disk drives, paths, directories, programs, subprograms, subroutines, device names, functions, operations, variables, filenames, and extensions.

This font also emphasizes lines of code that are different from the other examples. Removing Protective Screw Caps 5. Chapter 2 Installation and Configuration 7. Check the installation. Refer to Figure , Y-Splitter Cable.

Power on the chassis. To remove the unit from the PXI chassis, complete the following steps: 1. Power off the chassis.

Video Configuration Submenu Use this submenu to apply alternate settings to the video configuration. Trigger Router Configuration Submenu Use this submenu to program the front panel trigger router configuration. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual.